3000*2000 mm Horizontal Foam Slicer with 1300 mm Height for 2-300 mm PU Foam Cutting

The TDSA-2150 is a horizontal foam slicer with a soft belt conveyor table. Cutting size is 3000*2000 mm, cutting height is 1300 mm, thickness range is 2-300 mm, cutting speed is 0-50 m/min, motor power is 17.84 kW and machine weight is 3500 kg. The machine is CE certified.

Table size decides how many times a block is handled. A small table forces the operator to cut the block down before slicing, which costs a sheet, a set-up and a pair of hands. The TDSA-2150 carries a 3000*2000 mm table, so a block from the foaming line is loaded once and sliced through.

The 1300 mm cutting height is the second half of that. A tall block on a short machine has to be split twice, and every second set-up is a new chance to lose alignment. With the height and table matched, the block is squared once and the whole block is converted into sheets in one pass sequence.

• Model: TDSA-2150
• Cutting size: 3000*2000 mm
• Cutting height: 1300 mm
• Thickness: 2-300 mm
• Speed: 0-50 m/min
• Power: 17.84 kW

1. Load the block. Feed the block onto the soft belt with the cut face square to the blade.
2. Set the thickness. Enter the sheet thickness on the touch screen and confirm.
3. Start the suction. Hold the block flat on the table before the cut begins.
4. Run the pass. The table reciprocates and the band knife takes the sheet.
5. Remove the sheet. The soft belt carries the sheet clear of the blade line.
6. Repeat to the core. Continue until the block is reduced to the core.

Check the square of the first sheet against the block face. If the first sheet is tapered, the block was not squared against the blade, and every sheet after it inherits the error.

Every extra set-up on a block costs a sheet. When a table is too small, the operator squares the block with a hand knife, loses a slice to the saw kerf, and re-clamps before the real slicing starts. On a 3000*2000 mm table that step disappears, and the material saved on a few blocks a week pays for the size difference.

Handling is the second gain. A block that fits the table can be fed on the soft belt rather than lifted onto a bench, which is what keeps a two-person crew able to run the slicer alongside a peeler.

The third gain is consistency. A block squared once keeps its reference face through every sheet, so thickness drift across a long block stays inside tolerance instead of being reset at each re-clamp.

• Material: one set-up instead of two saves a sheet per block.
• Handling: belt feeding replaces lifting onto the table.
• Consistency: one reference face through the whole block.

• 3000*2000 mm table: the table takes a full block straight off the foaming line without pre-cutting.
• 2-300 mm thickness: one machine covers thin mattress sheets and thick cushion slabs.
• Vacuum suction: the sheet stays flat on the table instead of slipping under the band knife.
• Soft belt conveyor: blocks feed in and sheets leave without manual handling.
• Touch screen control: thickness is set on the panel and repeats to the next block.
• 0-50 m/min speed: feed rate is trimmed to the foam density being cut.
• CE certified: export-ready guarding and electrics.

• Mattress foam: block splitting into topper and core sheets.
• Furniture foam: sofa and seat cushion sheets in medium density.
• Packaging foam: uniform cushion sheets for protective packaging.
• Composite foam: sheets prepared for laminating and contour cutting.
• Sound insulation: absorption foam cut to fixed thickness.
• Contract cutting: short runs of custom thickness sheets.

• Isolate the machine before changing or tensioning the band knife.
• Keep hands clear of the blade entry while the table is moving.
• Use the pusher for the last section of a thin block.
• Lock out the conveyor before clearing a jam.

• Check band knife tension at every shift start.
• Clean the conveyor belt and vacuum filter daily.
• Grease the table guides weekly.
• Record blade hours and replace on schedule, not on failure.

The machine travels in an export-grade wooden case with the electrics protected and the cutter or blade assembly braced separately. Machine weight is 3500 kg and the overall dimension is 7000*4500*2500 mm, so the unit is quoted against a 20ft or 40ft container depending on the line it ships with.

A packing list, wiring diagram, operation manual and CE declaration travel with every unit. Delivery is 45 working days after downpayment; installation and commissioning support is available remotely or on site.