2-300 mm Thickness Touch Screen Digital Control Foam Slicer with 3000*2000 mm Cutting Size

The TDSA-2150 is a horizontal foam slicer with touch screen digital control. Cutting thickness runs from 2 mm to 300 mm, cutting size is 3000*2000 mm, cutting speed is 0-50 m/min, motor power is 17.84 kW and machine weight is 3500 kg. The machine is CE certified.

Thickness is the number the customer measures. A slicer that needs a hand wheel and a trial cut for every change spends more time setting up than cutting, and the operator ends up leaving one thickness on the machine all week because changing it is slow.

The TDSA-2150 sets thickness on the touch screen and the table reciprocates automatically to that setting. The 2-300 mm range covers thin topper sheets at one end and thick cushion slabs at the other, so a mixed order book runs on one machine without a second slicer.

• Model: TDSA-2150
• Thickness: 2-300 mm
• Control: Touch screen
• Cutting size: 3000*2000 mm
• Speed: 0-50 m/min
• Power: 17.84 kW

1. Enter the thickness. Set the value on the touch screen for the order.
2. Check the blade. Confirm the band knife is tensioned and tracking.
3. Cut a test sheet. Take one sheet and measure it at both edges.
4. Trim the setting. Adjust by the measured difference, not by guesswork.
5. Run the order. The table repeats the setting for the rest of the block.
6. Log the setting. Keep the value with the order so a repeat run starts on target.

Measure a test sheet at the leading edge, the middle and the trailing edge. If the three readings differ, the block moved during the pass, and the vacuum or the belt is the place to look.

A slicer set by trial cut wastes at least one sheet per change. Across a week of short orders that is more foam than most plants expect, and the scrap is thin sheet that cannot be sold or reused easily.

Digital setting also removes the operator variable. Two operators on two shifts will set a hand wheel differently by a fraction of a millimetre, and the customer notices across a shipment. A stored number keeps the whole order inside the same tolerance.

The 300 mm top of the range matters as much as the 2 mm bottom. Cushion and packaging work needs thick slabs, and a machine limited to 100 mm forces those orders onto a second process.

• Material: no trial sheet per thickness change.
• Consistency: the same number across shifts and orders.
• Range: 2 mm to 300 mm on one machine.

• 3000*2000 mm table: the table takes a full block straight off the foaming line without pre-cutting.
• 2-300 mm thickness: one machine covers thin mattress sheets and thick cushion slabs.
• Vacuum suction: the sheet stays flat on the table instead of slipping under the band knife.
• Soft belt conveyor: blocks feed in and sheets leave without manual handling.
• Touch screen control: thickness is set on the panel and repeats to the next block.
• 0-50 m/min speed: feed rate is trimmed to the foam density being cut.
• CE certified: export-ready guarding and electrics.

• Mattress foam: block splitting into topper and core sheets.
• Furniture foam: sofa and seat cushion sheets in medium density.
• Packaging foam: uniform cushion sheets for protective packaging.
• Composite foam: sheets prepared for laminating and contour cutting.
• Sound insulation: absorption foam cut to fixed thickness.
• Contract cutting: short runs of custom thickness sheets.

• Isolate the machine before changing or tensioning the band knife.
• Keep hands clear of the blade entry while the table is moving.
• Use the pusher for the last section of a thin block.
• Lock out the conveyor before clearing a jam.

• Check band knife tension at every shift start.
• Clean the conveyor belt and vacuum filter daily.
• Grease the table guides weekly.
• Record blade hours and replace on schedule, not on failure.

The machine travels in an export-grade wooden case with the electrics protected and the cutter or blade assembly braced separately. Machine weight is 3500 kg and the overall dimension is 7000*4500*2500 mm, so the unit is quoted against a 20ft or 40ft container depending on the line it ships with.

A packing list, wiring diagram, operation manual and CE declaration travel with every unit. Delivery is 45 working days after downpayment; installation and commissioning support is available remotely or on site.