600mm Cutting Height Foam Bevel Cutting Machine with 1000kg Frame and 0-30 m/min Feed

• 2000 x 1000 x 2000 mm footprint: the machine fits a workshop bay that a large bevel line cannot use, and it needs no separate foundation beyond a level floor and four anchors.
• 1000 kg welded frame: the mass and the stress relieved box section absorb the load of a dense block, so the blade line holds without a second operator holding the part.
• Single operator cycle: one person sets the angle, feeds with the pusher handles and stacks the parts, which keeps the labour cost of a bevelled part close to a square cut part.
• 0 to 30 m/min feed: the frequency converter lets a small shop run slow on a dense rubber plastic part and fast on a soft sponge order without changing the machine setup.
• 45 to 90 degree head with positive detents: the three common angles are found by feel and confirmed on the scale, which shortens the learning time for a new operator.
• Guarded blade and low voltage control: a compact machine still carries the guarding, the low voltage circuit and the emergency halt switch of the larger frame.

• Angle head: the cutting head swings on a machined pivot and locks through a calibrated scale, so a 45° chamfer and a 90° square edge are set with the same handle.
• Blade carrier: a guided carrier keeps the alloy blade tensioned along its full length, which holds a straight line of cut through dense block foam.
• Feed table: 1500 * 2500 mm of flat steel with roller support, so full blocks slide to the blade without lifting.
• Frame: welded box section, stress relieved before machining, which keeps the head square after years of loaded passes.
• Control box: IP54 enclosure with low voltage circuit, frequency converter and an emergency halt switch on the operator side.

• Mattress and upholstery: chamfered edges on PU overlays, seat cushions and backrest foam, where a true 45° corner decides how the cover sits.
• Packaging converters: 45° bevel cuts on EPE and EVA inserts, corner profiles and protective trays that must fit a carton without gaps.
• Footwear and gasket production: angled trimming of rubber plastic foam soles, seals and insulation strips in short and medium runs.
• Filtration and cleaning products: wedge cutting of sponge blocks for filter pads and cleaning rollers, where the angle controls flow.
• Furniture workshops: small batch bevelled foam parts for chairs, headboards and armrests, cut to drawing without a second machine.
• Construction and insulation: angled foam profiles and pipe insulation segments cut on site or in a workshop bay.

1. Set the cutting head to the drawing angle with the scale and the locking handle, then confirm with the angle gauge supplied with the machine.
2. Set the frequency converter to a feed speed that suits the foam density, slower for dense rebonded foam, faster for soft PU sponge.
3. Load the block on the feed table and align the reference edge against the guide, so the bevel line follows the block length.
4. Feed the block through the blade at a steady rate, keeping both hands on the pusher handles and away from the blade line.
5. Return the block, check the bevel against the sample, and adjust the angle or speed before the batch continues.
6. Stack the finished parts on a flat pallet, because a bevel cut part keeps its shape only when it is not pressed while cooling.

• Choose the standard angle head when the bulk of your work sits between 45° and 90° and the block height stays under 600 mm.
• Choose the roller feed table when your blocks are longer than 2000 mm, as a long block needs support at both ends.
• Order the 220 V or 440 V version at the time of the order, as the control circuit and the motor are built to the ordered voltage.
• Add a spare blade and a spare guide wheel to the first order, since these are the two parts that wear on a bevel machine.

Place the machine on a level concrete floor with at least 1200 mm of clear space on the operator side and 800 mm at the blade side, then anchor the four feet. A machine that is not anchored will walk on a loaded bevel pass, and the angle will drift over a shift.

Connect the three phase supply through an isolator rated for the motor and check the blade rotation direction before the first cut. Set the blade tension with the gauge on the carrier, fit the guard, and run an empty cycle at each of the three working angles so the operator learns the changeover before production starts.

• The blade is guarded on both sides during the pass; the guard is removed only for a blade change and the isolator is locked out first.
• The emergency halt switch is within reach of the operator position and tested at the start of every shift.
• Feed with the pusher handles only, and keep hands at least 200 mm from the blade line during a loaded pass.
• Only one operator runs the machine at a time, and the second person stays clear of the discharge side.
• Wear cut resistant gloves and eye protection, since foam dust and blade swarf leave the cutting zone at speed.

Each machine is run for 30 minutes at 45°, 60° and 90° before packing, and the bevel of a sample block is checked against a steel square. The motor current is logged at the duty load, the frame is checked for square after assembly, and the serial number is stamped on the frame plate so that a spare part order can be matched to the build. A CE declaration and a test report travel with every set.

The machine ships nude packed with plastic film and foam sheet, and the blade, angle gauge and small spare parts travel in a wooden case. A 2000 * 1000 * 2000 mm frame fits a 20 ft container with the head lowered. Delivery is about 30 working days after the down payment, and we send the loading photos and the packing list before the container leaves Qingdao.